You can easily make a fortune through the sale of different toy selections. It is a simple process which does not require any experience or training. You need to purchase a previous made doll or make one using clay. You also need to have a kit which contains relevant materials required in this process. Below are steps on how to make doll molds for sale to take into consideration.
Start by determining the kind of form to make. You can decide to make a one-dimensional object or three-dimensional depending on your market. A one-dimensional figure has a flat surface on one side whereas a three-dimension has two parts. Measure the object to make a containment box which can comfortably accommodate the respective object.
Construct the containment box. A containment box is required to pour the molds inside while reproducing the dolls. You can use any material as long as its edges are smooth to create airtight edges. The container walls should be at least one inch from object to allow enough space to fill the mold. Use glue to stick the edges if you want the box to work effectively.
Make the necessary preparation of your object. The one-dimensional object requires the flat side to be placed on a clay square or an easy to release compound. On the other hand, the three-dimensional object needs to be inserted on the adhesive material to the halfway mark. Ensure that the exposed surface is smooth before you go to the next step.
Mix the rubber mold. There is a variety of molding materials that one can use. Latex mold is quite affordable, but they take a long time to set. Silicon rubber epoxy is the best since it produces quality dolls. Reusable materials are ideal but are not good for heat casting although they can be melted again. Follow the instructions written in the kit to make the right mold.
Ensure the surface is ready before you pour the ready mold. Paint the surface of your mold with a smooth brush to ensure that every part of your object is taken into consideration. You should be careful while handling this process to avoid leaving out some important parts of your objects. You can pour the compound when you are certain that every detailed part has been covered.
Extract the work. A one-dimensional object does not have a lot of steps to consider while extracting the work. Start by tearing the containment box to expose the respective mold. Remove the object from the rubber and have the mold ready for use.
How to remove a three-dimension object. Start by tearing the containment box apart as well to expose half of the mold inside the square. Expose the clay or adhesive material as well and leave part of the rubber mold. Take a hobby knife and cut pyramid-like shapes which allow the two halves to join. Part of your halves should be applied with jelly to avoid having the two parts sticking while remaking the dolls.
Start by determining the kind of form to make. You can decide to make a one-dimensional object or three-dimensional depending on your market. A one-dimensional figure has a flat surface on one side whereas a three-dimension has two parts. Measure the object to make a containment box which can comfortably accommodate the respective object.
Construct the containment box. A containment box is required to pour the molds inside while reproducing the dolls. You can use any material as long as its edges are smooth to create airtight edges. The container walls should be at least one inch from object to allow enough space to fill the mold. Use glue to stick the edges if you want the box to work effectively.
Make the necessary preparation of your object. The one-dimensional object requires the flat side to be placed on a clay square or an easy to release compound. On the other hand, the three-dimensional object needs to be inserted on the adhesive material to the halfway mark. Ensure that the exposed surface is smooth before you go to the next step.
Mix the rubber mold. There is a variety of molding materials that one can use. Latex mold is quite affordable, but they take a long time to set. Silicon rubber epoxy is the best since it produces quality dolls. Reusable materials are ideal but are not good for heat casting although they can be melted again. Follow the instructions written in the kit to make the right mold.
Ensure the surface is ready before you pour the ready mold. Paint the surface of your mold with a smooth brush to ensure that every part of your object is taken into consideration. You should be careful while handling this process to avoid leaving out some important parts of your objects. You can pour the compound when you are certain that every detailed part has been covered.
Extract the work. A one-dimensional object does not have a lot of steps to consider while extracting the work. Start by tearing the containment box to expose the respective mold. Remove the object from the rubber and have the mold ready for use.
How to remove a three-dimension object. Start by tearing the containment box apart as well to expose half of the mold inside the square. Expose the clay or adhesive material as well and leave part of the rubber mold. Take a hobby knife and cut pyramid-like shapes which allow the two halves to join. Part of your halves should be applied with jelly to avoid having the two parts sticking while remaking the dolls.
About the Author:
Get a summary of the things to consider before purchasing doll molds and view our selection of porcelain doll making supplies at http://www.sandsfiredarts.com/about now.
You can easily make a fortune through the sale of different toy selections. It is a simple process which does not require any experience or training. You need to purchase a previous made doll or make one using clay. You also need to have a kit which contains relevant materials required in this process. Below are steps on how to make doll molds for sale to take into consideration.
Start by determining the kind of form to make. You can decide to make a one-dimensional object or three-dimensional depending on your market. A one-dimensional figure has a flat surface on one side whereas a three-dimension has two parts. Measure the object to make a containment box which can comfortably accommodate the respective object.
Construct the containment box. A containment box is required to pour the molds inside while reproducing the dolls. You can use any material as long as its edges are smooth to create airtight edges. The container walls should be at least one inch from object to allow enough space to fill the mold. Use glue to stick the edges if you want the box to work effectively.
Make the necessary preparation of your object. The one-dimensional object requires the flat side to be placed on a clay square or an easy to release compound. On the other hand, the three-dimensional object needs to be inserted on the adhesive material to the halfway mark. Ensure that the exposed surface is smooth before you go to the next step.
Mix the rubber mold. There is a variety of molding materials that one can use. Latex mold is quite affordable, but they take a long time to set. Silicon rubber epoxy is the best since it produces quality dolls. Reusable materials are ideal but are not good for heat casting although they can be melted again. Follow the instructions written in the kit to make the right mold.
Ensure the surface is ready before you pour the ready mold. Paint the surface of your mold with a smooth brush to ensure that every part of your object is taken into consideration. You should be careful while handling this process to avoid leaving out some important parts of your objects. You can pour the compound when you are certain that every detailed part has been covered.
Extract the work. A one-dimensional object does not have a lot of steps to consider while extracting the work. Start by tearing the containment box to expose the respective mold. Remove the object from the rubber and have the mold ready for use.
How to remove a three-dimension object. Start by tearing the containment box apart as well to expose half of the mold inside the square. Expose the clay or adhesive material as well and leave part of the rubber mold. Take a hobby knife and cut pyramid-like shapes which allow the two halves to join. Part of your halves should be applied with jelly to avoid having the two parts sticking while remaking the dolls.
Start by determining the kind of form to make. You can decide to make a one-dimensional object or three-dimensional depending on your market. A one-dimensional figure has a flat surface on one side whereas a three-dimension has two parts. Measure the object to make a containment box which can comfortably accommodate the respective object.
Construct the containment box. A containment box is required to pour the molds inside while reproducing the dolls. You can use any material as long as its edges are smooth to create airtight edges. The container walls should be at least one inch from object to allow enough space to fill the mold. Use glue to stick the edges if you want the box to work effectively.
Make the necessary preparation of your object. The one-dimensional object requires the flat side to be placed on a clay square or an easy to release compound. On the other hand, the three-dimensional object needs to be inserted on the adhesive material to the halfway mark. Ensure that the exposed surface is smooth before you go to the next step.
Mix the rubber mold. There is a variety of molding materials that one can use. Latex mold is quite affordable, but they take a long time to set. Silicon rubber epoxy is the best since it produces quality dolls. Reusable materials are ideal but are not good for heat casting although they can be melted again. Follow the instructions written in the kit to make the right mold.
Ensure the surface is ready before you pour the ready mold. Paint the surface of your mold with a smooth brush to ensure that every part of your object is taken into consideration. You should be careful while handling this process to avoid leaving out some important parts of your objects. You can pour the compound when you are certain that every detailed part has been covered.
Extract the work. A one-dimensional object does not have a lot of steps to consider while extracting the work. Start by tearing the containment box to expose the respective mold. Remove the object from the rubber and have the mold ready for use.
How to remove a three-dimension object. Start by tearing the containment box apart as well to expose half of the mold inside the square. Expose the clay or adhesive material as well and leave part of the rubber mold. Take a hobby knife and cut pyramid-like shapes which allow the two halves to join. Part of your halves should be applied with jelly to avoid having the two parts sticking while remaking the dolls.
About the Author:
Get a summary of the things to consider before purchasing doll molds and view our selection of porcelain doll making supplies at http://www.sandsfiredarts.com/about now.
No comments:
Post a Comment